All Posts

just add an output with Befaco OUT V3
Output Interface and Headphone amp

Void has been gone/inactive for a year or so now.

I bought a mixer that never shipped over a year ago. At 1st got some communication but then it went dark.
Not sure what happened, hope the person is ok but the site etc. is dead for a while now.

Hey guys,

i'm quite new on modular sound design.
I have been practising live instruments (piano, guitar, bass) since many years.
Playing in a live band, i want to add a modern and new layer of dark ambient tone.

My requirements are :
- input for external midi sequencer/keyboard (MC101 Roland) and clock
- output to the console mix
- good tones but not too expensive.

What do you think of this setup ? does it works ?

Many thanks for your support

regards

jerome

very interessting Module !

What has happened with Void Modular ?

A test case to see if i should just buy an all in one solution

or continue with smaller portable cases

They are in

As per the title, the Syntesla modules should be added since the store is online

Hi Guys

I add my Mother32 into a eurorack case.. what kind of effects would you add to it? Is Make Noise mimeophon a good choice for the M32? or is something like fx aid pro better for it?

Whats your prefer?

What about a Zoom Live Session with a couple of Modular Guys ?
Or in a Whats App Grouß with Vision. iam lokated in Hamburg Germany.
if you are interessted, send me PN.

In case anybody else runs into the same issue, I didn't need to boot Sweet Sixteen after the Disting. But what is imperative is to have the Disting Ex's i2c address set to 49 0x31. That's what Sweet Sixteen seems to use in Sweet_3 firmware, so that's what the Disting Ex needs to listen to.

*Plaits(1채널)
-1/64
-30%level, probability 90%, shape 사각펄스연속

Hey everyone,

Today I tested out this little live set — a mix of underground techno and drone at 165 BPM.

I made a small patch using the StolperBeat and the Voltage Block as sequencers to create pattern transitions. The Rample handles my drums and the Bohm my kick, both running through the 1010music FXBOX at the end of the chain. I use the Z8000 on the Rample to play the layers.

My mixer is the D.O.MIXX, and the drum compressor is the MESSOR.

For the drones:

The Polimaths generates LFO-like movements, which vary because the Spread parameter is modulated by another LFO, the Contour 1.
I use a Mysterion and two MMGs to create shifting rhythmic textures that I modulate with the StolperBeat.
The Plaits plays vocal-style voices that are amplified with Warps, and modulated by the Polimaths.
The Vhikk X creates drones also modulated by the Polimaths.
I mix all the drone layers with a Vortices.

Thanks for listening — see you soon! ;)

*Plaits(1&2 채널)
-Morph 로 톤조절

Hey I finally got around to designing a front panel for this thing. Looks pretty cool to have a mass of functionality in 18 HP!

As an owner of this module it kicks ass but the DJ/ducking module has a bad "level" which results in your very good other modules sound quality decreasing (i would say loosing headroom and precision)
It was so pronnonced for me... that my style had changed with it...
Moreover I was loosing output level control
What about you ?

Hi everyone,

Maybe someone can help me. When I want to add loops from the Bitbox Micro to my other sounds, does it only work if the loop was originally recorded at the same clock speed? Clocking the loop with Pam’s doesn’t work, because then it keeps trying to restart the loops or something like that, which results in strange sound output. Can I only use single-shot samples with Pam’s in order to sync them to the timing of the other modules that are connected to Pam’s?

For example, if I’m running my Brains path at 90 BPM and I want to play a loop on the Bitbox Micro that is at 110 BPM, is there any way to bring it down to 90 BPM? When I try to do it through Pam’s by setting one input on the Micro to “clock” and connecting it to Pam’s, the loop behaves very strangely and becomes unusable…

Does anyone know a logical explanation? Sorry… I’m a beginner.

Thank you very much and best regards.

Howdy! What are you using to control the D? If you're using the MIDI in I can't tell you what's wrong, but the main thing that comes to mind is that you need to gate both the filter contour and the loudness contour for it to sound. As far as tuning is concerned, the knobs for osc 2 and 3 go 5 full tones away in either direction, so you may need to change the octave if you're still not able to match pitch. If that still doesn't work it may need some calibration and that's past my ability haha

Happy bleeping!

After a grueling day that tests your every nerve, hitting the jackpot of relaxation at Fast Payout Casinos becomes more than just an indulgence - it's an earned right! These casinos redefine speedy satisfaction by cutting down tiresome waiting times, guaranteeing swift withdrawals without hassle. Imagine exchanging stress-outs for adrenaline rushes in mere moments. With top-notch security measures ensuring that your hard-earned treasure is delivered practically instantaneously, it's as if these https://ictir2016.org/ Fast Payout Casinos are welcoming you with open arms into a realm where time is money, and they respect every golden second you’ve spent. Coupled with exhilarating games that promise fun at every turn, Fast Payout Casinos are not just about playing but winning back your peace of mind. You deserve this unparalleled blend of exhilaration and efficiency - a potent cocktail served straight up to turbocharge your unwinding rituals!

EDITED Dec 1st, 10:47

I contacted Erica Synths and they have confirmed there is an issue with the internal quantizer that is making the first note sharp on all the GVCO modules.

If I get a fix from them I will update the post.

EDITED Nov 29th, 00:31

Hello all,
I took my Model D out of its desktop case and put it into my Behringer GO Case. Per the manual, the model d is plugged into one dedicated section of the GO case, but when I go from the main pout into the in on my Erica Synths sterio mixer....nothing. Volume on the model d, mixer, and even the input on my interface set to max and only get the FAINTEST sound.

When its in the desktop case its fine. Does the desktop case wiring have a built in VCO and thats why it only works in desktop mode? Im debating getting a 2HP linear VCA from sweetwater and seeing if that helps.

When tuning the model d one of the oscillators also wasnt in tune and i cant turn the tuning thing enough to get it in tune. Is the synth just a bust?

Such a great module – I set up the A/B midi outputs in under a minute right from the front panel. It’s a modern replacement for the Deft Audio Midi Thru module, but with midi merge and three extra outputs on top. Highly recommend!

I would add a filter for behringer brains.. behringer surges is very cheap and sound realy solid.. i have one and i like it a lot

EDITED Nov 27th, 08:21

Just added the Hotone Ampero II Stage but it didn't remove the white background. I tried to upload a better capture but it isn't showing up.

Any help would be appreciated.

Rack Stats Reset

Visits counter of racks resettet. See here

Keep me logged in! refactored

The Keep me logged in! function now uses a more modern, security-focused token workflow. In practice, this means that even if you checked that box on a computer that isn’t yours, you can now log out from any other device and instantly revoke that persistent login.
It isn’t compatible with the old system, so many people will have to log in manually over the next few days.

Hello,

If anyone is working on AI integration, please reach out via PM if you see any of the following as a good 'match' for your project.

I have been working on an AI back-end framework for modular synths and it is now ready for BETA testing.

Please know it's not a complete solution, only the critical parts of the back-end and hardware framework required to implement AI. ( the parts needed no matter what AI solution type is implemented, like packet protocols, module addressing, interface to 'train' the model, saving/loading module settings to/from cloud, javascript node API etc )

It's difficult to summarize but here is a partial list of what I have finished so far. I'm focused on clock and sequencer AI to start. ( find good clock/polyrythm/sequence combos and share them with others )

• Web browser/iOS/iPAD app. ( allow user to 'like' or train the AI as part of the control surface )
• Protocol to 'chain' modules together and auto-address via 3 wire cable. ( automatically tell the AI what devices are on deck )
• Load/save module settings to localstore/eeprom/cloud via node/javascript. ( provide framework for any integration )
• Communicate with an AI server back end, passing the data required to do AI back and forth.
• Auto firmware updates from browser. ( encrypted bootloader )
• Packet protocol to communicate between browser/cloud and hardware modules. ( this has been my main focus for several years now )
• Full API on a dedicated 'STM32'. Can be 'dropped into' existing project or 3rd party modules like an ASIC

If sees this as a good match for their project, PM me and we can discuss in detail. It's quite a large project for just 1 person :)

The api guide can be found here: https://roboDNA.com

Building a (second) minimal techno live setup in a (smaller) retro samsonite case!

Building a minimal techno live setup in a retro samsonite case!

In this video I’m working on a new minimal-music piece in 10/4. Tom, a good friend of mine and a classical composer, has been teaching me about minimal music and this piece is a result of that. The core of the piece is a quartet of STOs that I can really play by shaping envelopes, opening and closing filters, and working with reverb, delay, and low-pass gates to keep everything organic. Plaits runs through Multigrain and Sealegs to create a warm layer underneath. I’ll perform this piece live with Estroe this Friday as we open for Andrea Cichecki. If you’re in the Netherlands, come join us at Lab-1 in Eindhoven.

[media]

EDITED Nov 25th, 21:09

It would maybe be possible to examine this further, but it's not going to change the fact that your module is behaving strangley. It would indeed be interesting to hear from someone with the same module.
-- e_v_k

I'm guessing its not a very common or popular module ? No one with one has chipped in at all. I have sent a video to Erica Synths but not heard anything back on it so far.

EDITED Nov 25th, 19:59

It would maybe be possible to examine this further, but it's not going to change the fact that your module is behaving strangley. It would indeed be interesting to hear from someone with the same module.

Will look into that BASTL citadel, thanks for the suggestion.

noodle_hut,
Stop.pretty please. and for the very last time....I'm not quantizing an already quantized note.

EDITED Nov 25th, 18:23

EDITED Nov 28th, 15:45

noodle_hut,
Please stop now. I know how a quantizer works. I know you are trying to be helpful but you keep dismissing what I say and just plough on with the same repeated info. Just stop before you respond and think for one second about what I am telling you.

I feed into the GVCO 0.000V and it produces a C. Its internal tuner tells me its a C and my Peterson Strobe tells me its a C.
I turn on the internal Quantizer and the pitch changes to C Sharp. This is shown by the GVCO's inbuilt tuner and my Peterson.

Just forget everything else for now. There voltage is 0.oooV so its not near the cusp of where the quantizer wants to round up to the next semitone. We are not changing the voltage entering the GVCO at all. Just turning on its quantizer.
Are you telling me that this is a quantizer that is working as it should?

Anyway, as I said earlier. Lets draw a close to this now as we are not really getting anywhere other than arguing back and forth and I don't want to continue.

I thank you again for your time though.

EDITED Nov 25th, 16:17

EDITED Nov 28th, 15:47

Get an analog voltage source (not a digial one) and monitor it with a digital voltmeter, to at least hundreths precision.
Set your Erica to quantize and feed that voltage to it, from 0v to 5v.
Observe the voltage when the oscillator jumps to the next half step.
Is it when the input is just past ~((1volt / 12.0) * note), or just before?
Or does it flip when the to-be-quantized voltage is past half way between?
Round up or round down or mid-nearest. Or maybe some internal rules table or something.
I couldn't find the quantizer's rules in the vco manual, it just says how to turn it on and set it.

Anyway, now read the voltages from your digital sequencer as it runs a chromatic scale.
Are they each a 'precise' 0.0833333333333333333333 volts apart from each other?
Or 0.0830, or 0.0820, or 0.085?
Analog. Squishy.
There is an implied imprecision down in the 0.003333333s, especially when you're adding them together.
And so there is no "C", or 'in tune', just 'sounds in tune', even when it never really can be.
An analog quantizer can only approximate what your intent for 'C' is, and they all can do it differently.
It's a best guess, because your sequencer isn't sending 'A', it's generating ~0.8333333 volts. Give or take.

Now, knowing the vco's quantizing behaviour, you can see why it is doing what it does and when.
I still think your oscillator is working correctly.

Don't quantize already quantized CVs. You'll get stray semitone errors.

I never like it when someone asks for help, and the annoying reply is 'Why are you doing that'?
But, why are you doing that?

-- noodle_hut

Hello noodle_hut.
I have just measured ( for the last time ) the voltage coming from my sequencer for the first step ( the C ) and its 0.000V
So a precise voltage. I can send you a picture if you do not believe me. Its about as perfect a voltage as you could hope for.
The GVCO plays C when its given this voltage as I would expect it to. If I turn on the intermal quantizer the GVCO produces C sharp. I don't know why you are insisting that this is anything other than wrong.
I don't think we are getting anywhere with this so probably best I stop asking for help now.
Once again, thanks for your input.

"> What's the voltage range you're using? 0-1V or something higher? What about the result for several octaves, is it only the lowest note that's sharp?"

-- e_v_k

The range is 0V to +5V in this experimant. Transposing up tones, semitones or octaves yeilds the same result and just the first note is sharp.

In response to a question you asked earlier that I missed... When the eronious C sharp plays the GVCO tells me its playing C sharp. It doesn't think its playing C but outputting C Sharp.

I did some new experiments with the internal quantizer on this morning and here are the results please take it as read that with the quantizer off all sequences play back as expected as it does if I use an external quantizer.
If I send in a sequence that is C then C one octave up the two notes play back at the same pitch. If I increase the interval between the two Cs by another octave I get a one octave interval, this behaviour is the same when the quantizer is set to chromatic or octaves.

I also tried another experiment inspired by noodle_hut.
If I create a chromatic sequence by ignoring the voltages coming from the sequencer and just setting them by ear, I can get the GVCO to play back a chromatic scale ( with the internal quantizer on ) but every note is a semitone sharp above what the GVCO its tuned to when the quantizer is off. So in some ways one could argue it is, kinda, working.

But I have access to six other quantizers and not one of them produces the results the internal quantizer does. They all work as expected and what you put in you get out ( unless you put in a rouge voltage and then that gets corrected/adjusted so the resulting note is what was desired )

Hello fellow Eurorackers,

I have been building my own racks since I first fell in love with modular many years ago. During this time I experimented with different materials, electronics as well as with my own "hacks" for cable management.

This is my first case that is ready to be sold that contains all the lessons learned. Every screw, component and material have been carefully chosen to be of highest quality and if you hate cable spaghetti you will love the special features.

I hope it will bring you as much joy as it does to me.

• 3 x 126 hp with threaded inserts

• Integrated power supply & bus boards (Konstant Lab):

  • HAMMR 100 Power Supply Unit
  • 3x Bus Boards (16 connectors each)
  • Power Brick (Meanwell 120W) with Power Cable

• Special features

  • Dust-proof Air Filters
  • Channels and Wormholes for Cable Management
  • Cable Connection Cogs
  • Shelf for Powerbrick and Patch Cables

• Dimensions

  • Width: 700 mm
  • Height: 350 mm
  • Depth: 350 mm
  • Weight: 13 kg

All components are produced in EU. Each box is assembled by my hands :)

Professional Electronics
I want only the best for your modules. That is why I partenred with Konstant lab, the market leader in eurorack electronics. DRONEBox has a built-in HammerPWR, a whopping 100W power supply, which is plenty for even the most hungry modules. It comes with a 120W power brick (Meanwell GST120A-P1M) as well as three pocket bus boards for each row, so all you have to do is plug in your favourite modules.

Outputs: +12V / 5A (splited to two branches 2.5A + 2.5A), -12V / 2.5A, +5V / 2A
Input: 20V DC
Protections: Input filter, Input overvoltage. Input reverse polarity voltage protection. Output overvoltage. Output short circuit – automatic recovery. Output over current – automatic recovery. All output protections are independent for each rail.

Efficiency: 90%

Additional: Dual input common mode LC filter with high efficiency of canceling noise and interference from input connector. Additional input filter for each converter for minimal output noise and interferences. LEDs indicate present and drop of output voltage. +12V output is splited to two branches for modules separation and minimalize of voltage dropout.

For all other features (which there are many), visit my website drone-audio.com

And since Black is the color of DRONE AUDIO, there is a one-time limited offer for Black Friday!

EDITED Nov 25th, 12:16

We’ve always had a counter on the rack pages that shows how many users have viewed a rack.

This counter also recorded visits from people who were not logged in. Over the years, most of those turned out to be bots, AI spiders, and web crawlers. The table grew to around 150 million rows. We had no reliable way to distinguish real traffic from automated traffic, so we now only count visits from logged-in MG users. All visit entries from non-logged-in users have been deleted. Which is a drastic 95% decrease for most racks.

We never considered this statistic particularly important, but unfortunately some people cared about it and are upset about the change. There was no bad intent behind this change!

Don't know what kind of music you're making using the modules. Some general advice for a secondary rack. A nice modular sequencer would be a good choice, some of them have a distinct workflow that differences a lot from the normal standalone one. Good effects with modulation is also a good idea.
There's a sampler by 1010 music in the rack, but if you're interested in some hard music, dance music, try some analog kick and hihats.

Don't know what kind of music you're making using the modules. Some general advice for a secondary rack. A nice modular sequencer would be a good choice, some of them have a distinct workflow that differences a lot from the normal standalone one. Good effects with modulation is also a good idea.
There's a sampler by 1010 music in the rack, but if you're interested in some hard music, dance music, try some analog kick and hihats.

Behringer modules are good for beginners, and they're where I first started. The more you play you'll notice the differences in sounds of behringer products. Try to use the modulation and utilities stuff more in Behringer. For cheap oscilator modules and effects modules, there're lots of other options sounds better but only slightly expensive than behringer.
1010 sampler is good, but you might have to suffer from a lot of menu diving to use the details. Doesn't mean that it's not good, just a gentle reminder if you really care about this.
I'd recommend the new Bastl Citadel series, for any use. It now has three firmware, covering synthesizer, effects, and sampler. Good for a supplement and if you 're bored with one function, you could' switch another one easily. It has built in cv, pattern generator and midi support that makes it a nice utility in the system too.

I'm now using a 104hp 7U perfromance case and would want to limit all my useful, important modules for performance and travel inside. I wish to know are there any advice on disigning this size of rack and how to utilizt the space.
This is the rack I'm currently using (The third row is a 4ms 64pods, which I use for light travel and jam):

And this is my current plan:

I wish my main case could take charge of most techno and house performance and still provide me some space for doing ambient. The 4ms is mostly as a portable option for me to take some out and go to a park for a simple jam.
Some point I'm hestitating:
1. Shall I remove the BOC+SED and replace the combo with a doepfer 111-6 synth voice? The rides in the storm modules sound good but it just takes too much space in total (20hp, comparing with 10hp of the doepfer one).
2. Erica synth Black Hole DSP2 sounds good and I really like the knobs, but still it is a little big large. I'm thinking to change it with a Mimeophon, or a granular effect like Mojave or Beads. Which option might be better?
3. How many mixer is needed? One cockpit would not satisfy all the need. Can a VAC mixer solve the problem? or should I get another 1U small mixer? (I'm not gonna buy any large performance mixer until I have two intellijel case)

Feel free to ask the product I've owned if you're interested.

Yeah, the Space FX is basic and not great, however it's a super cheap option so I was able to get two inexpensive units to mess around with. I decided to do the Space FX full wet signal on one of them. I was playing around with it over the weekend of feeding the signal of one into the second one then back into the first one. Combined with a VCA I was able to get some pretty fun distortion, mostly combining the Ambience on the wet-dry signal one, then Echo on the full wet signal one. I had a lot of fun messing around with it for a while, but the sheer lack of CV control is the killer. That will make for a future DIY mod for me.
But at the end of the day I get better FX through my mixer / workstation (I picked up an old Yamaha AW16G for cheap and it's filling in a lot of gaps in my setup for the time being). I will probably pop out the Space FX when I can get something better, maybe have a little diy side unit for quick fx hits, we will see.

I appreciate the feedback!

EDITED Nov 28th, 15:46

What's the voltage range you're using? 0-1V or something higher? What about the result for several octaves, is it only the lowest note that's sharp?

Thanks for your input e_v_k.

So I tried a new experiment today and created a 5 step sequence that consists of C D E G A ( pentatonic major ).
Without the quantizer enabled I get that exact sequence played back. If I turn on the internal quantizer and set it to pentatonic major I get D D E G A. So the first note is now a whole tone sharp. If I change to quantizer to chromatic I get C Sharp as the first note followed by all the correct notes.
If I go back to me original sequence and play it back with the quantizer on and set to chromatic I can get the first note to play C by detuning the "tune" knob by about 48 cents but all the other notes that follow are now out of tune.

I'm still sctarching my head on this one.
What I really need is someone else that has a GVCO to try the same experiments and see what results they get.

EDITED Nov 24th, 19:09

Smart transaction with @PandorasBox
Module in very good condition.
Recommended Seller !