Dimensions
15 HP
42 mm deep
Current Draw
79 mA +12V
46 mA -12V
0 mA 5V
Price
$430 Price in €

This Module is currently available.

HM1973mk2: Tyme Sefari is a voltage-controlled audio buffer designed for live resampling of music

TRANSPORT CONTROL

The buffer operates in a circular manner, meaning that when the end of the memory is reached, the playback and recording position reset to the starting position. When the PLAY switch or gate input (P) is active, the contents of memory will be sent to the audio output jacks, and the playback position will advance. This mode is indicated when the YELLOW LED is lit. When the REC (R) control is active, new data will be taken from the audio input and written into memory. This mode is indicated when the RED LED is lit. The DIR jack (D) and switch control the direction of playback/recording, and can be modified in real time. The SAMPLING FREQUENCY control determines the speed of playback and recording. Note that if PLAY is not active, then no RECording will take place until PLAY is made active again. It is the master control for the operation of the transport.

If the LOOP switch or gate jack (L) is active, then the travel of the play and record "heads" within the memory buffer will be constrained. Use the START and END sliders to define the window of playback. If the START position is set to be greater than the END position, then the direction of travel will be reversed.

The LOOP sliders can also be disabled by activating the TAP TEMPO toggle switch. In this mode, the recording and playback length will be determined by the time between button presses (or gate input events) of the TAP TEMPO control group. This control will begin to modify the loop length after four (count 'em, four) button presses or gate inputs are made. Subsequent presses will be averaged into the determined tempo value.

When the loop end point is reached in all modes, the orange LED near the slider will briefly light up, and a trigger event will fire from the TAP TEMPO OUTPUT jack.

The four transport controls will activate their function if the switch is in the UP position, OR if the gate input is currently reading a HIGH signal. This enables remote control or automation of the four parameters, as well as advanced audio effects when modulated at faster-than-human rates.

ANALOG I/O

The FEEDBACK control mixes part of the output audio back into the input amplifier, with optional inversion set by the associated toggle switch. An input jack is provided here, so you may break the feedback loop by patching in an alternate signal. By using the additional output jack, an external processor, and this FEEDBACK input jack, you may insert different effects into the feedback loop such as a filter effect, for behavior similar to an "analog" delay device. Two main audio outputs are given. The upper is a "MIX" jack with the signal's wet/dry ratio set by the associated knob. The bottom jack is simply the output of the recorded signal with no dry signal mixed in.

CV INPUTS

The large controls for LOOP START and END, and SAMPLING FREQUENCY all have smaller CV attenuators attached to them as well. When these small knobs are adjusted to the center position (so that the knob sits in the center detent), no signal from the associated CV jack will be passed to the parameter. When the attenuator is turned counter-clockwise, the CV input will be subtracted from the parameter value. When it is turned clockwise, it will be added to the parameter. The voltage specifications for each CV input (as well as all other inputs) are given on the panel. Voltages outside of these ranges will not harm the module unless they exceed +/- 12V DC, but they will not have any additional effect outside of the specified range.

NONVOLATILE STORAGE

The MEMORY SAVE button will pause the audio for a few seconds and write all of the memory contents to non-volatile backup. This means that you can recover it after the module has been powered down. If a jumper is installed across the "WRITEPROTECT" pins on the back of the module's circuit board, this button will have no effect.

The MEMORY LOAD button will retrieve the contents of the memory backup and place it into the recording memory. This will also stop audio for a few seconds. When you first obtain this module and install it in the rack, I suggest pressing this button first. I left a surprise in there for you.

If you hold down the TAP TEMPO button and press the MEMORY LOAD button, the recording memory will be blanked out for your convenience.

SUGGESTED APPLICATIONS

ONE-SHOT SAMPLER

Disable the PLAY control, and re-activate it by flipping the switch or activating the P gate input. When this happens, the sampler will automatically reset to the memory (or loop) start point for predictable sample playback, useful for dialogue, percussion, or other sonic events where a strictly defined start time is important.

DELAY EFFECT

Turn the FEEDBACK control up and activate LOOP, PLAY, and REC controls. The position of the LOOP sliders will determine the length of your delay. Note that the loop sliders have a limited resolution, as they must traverse a great deal of memory. Great care has been taken to provide a click-free delay effect in this mode, but should you require a finer loop resolution you must use the TAP TEMPO mode in this delay configuration instead.

THRU-ZERO DRONE

PLAY back a recorded segment of audio. Patch an audio-rate square wave into the D input. This will result in a thick, chorused pitched drone with no added discontinuity. Adjust the pitch of this tone with the SAMPLING FREQUENCY control, and the length of the waveform by adjusting the input square wave. Note that any deviations from 50% duty cycle in this square wave will result in the "window" shifting in memory. Play with the loop sliders for additional effects.

FALSE TIMESTRETCHER

PLAY back a recorded segment of audio with LOOP active. Set the START slider to minimum. Set the END slider nearby, so a very short loop is played. Now, take an external, slow ramp LFO voltage and apply it to both the CV START and END inputs in equal amounts. Vary the speed of the LFO to control the speed of the "timestretched" playback.

SOUND OF THUNDER EXPANDER

CONNECTION

Remove your Tyme Sefari from the rack and view the two 10-pin headers named "THUNDER" and "THUNDER2". Connect the two ribbon cables from the SOUND OF THUNDER to these headers, making sure the red bands point down. Install both module and expander into the rack.

OPERATION

The SOUND OF THUNDER adds several optional modes to the Tyme Sefari, activated through 8 sets of toggle switches and gate inputs. Like the Tyme Sefari, the parameter is active if the switch OR the gate input is high. The gate inputs are provided to automate control of this module's deep functions, and to present further sound design possibilities. For example, the stereo and format controls change the way that audio data is encoded AND decoded from memory, but the data in memory is not tagged with its proper format description. If you record in one format, but then playback in another, new, extreme distortion effects may be heard depending on the combination of modes used for recording and playback.

FORMAT SWITCHES

The first two switches change the audio recording and playback format. The default setting is 16-bit linear. The other formats are as follows:

  • 12-bit linear. This is stored into memory with the bytes swapped, and restored to normal when played back.
  • 12-bit logarithmic (µlaw) - This setting doubles the amount of memory available for recording, and slightly increases the maximum sampling rate.
  • 8-bit linear - This setting doubles the amount of memory available for recording, and slightly increases the maximum sampling rate.

PITCH SHIFT MODE

This mode changes the behavior of the SAMPLING RATE control. When active, the rate of recording is fixed. The playback rate is variable, with the center position of the large knob meaning that there is no pitch shift. Turning the knob counter-clockwise results in a downward pitch shift, and turning it clockwise results in an upward pitch shift. Try this in "delay" mode with lots of feedback for some interesting harmonic staircase effects.

STEREO MODE

This mode enables the right channel input and output seen on the lower half of the SOUND OF THUNDER expander. When this switch is active, the right channel data will be interleaved in memory with the left channel. The feedback is a monaural sum of the two output signals, applied to both inputs. When engaged, this mode will cut the available recording time in half, and also reduce the maximum sampling rate.

BEND SWITCHES

This group of four switches will interfere with the address and data busses of the TYME SEFARI MARK II. Effects similar to a "circuit bent" toy keyboard will be heard as these switches perform identical functions.

power tested in 2021 with a joranalogue test3 module, and just idling, it differs quite a bit from what the draw reportedly was,

http://www.industrialmusicelectronics.com/products/7


Ø 4.26 (27 Votes) Average Rating
submitted Oct 11th 2012, 18:39 by solitud | last Change Oct 17th, 06:56 by MoltenReplica

92 Users are observing this

Affiliate Disclosure
This page contains affiliate links from eBay, Reverb.com and other partners for which ModularGrid may be compensated.

USA

Three Wave MusicControlDetroit ModularNoisebugPerfect CircuitControl Voltage

Canada

Nightlife ElectronicsMoog Audio

Australia

Found Sound

These merchants probably sell this module. Huh?